Integrated Circuits (ICs)

MAX211IDW

Obsolete

Texas Instruments

5-V MULTICHANNEL 120KBPS RS-232 LINE DRIVER/RECEIVER WITH +/-9V OUTPUT & +/-15-KV ESD PROTECTION

Integrated Circuits (ICs)

MAX211IDW

Obsolete

Texas Instruments

5-V MULTICHANNEL 120KBPS RS-232 LINE DRIVER/RECEIVER WITH +/-9V OUTPUT & +/-15-KV ESD PROTECTION

Specifications Series Pricing CAD Description Documents

Technical Specifications

Parameters and characteristics for this part

Specification	MAX211IDW

Data Rate	120 Kbps
Duplex	Full
Mounting Type	Surface Mount
Number of Drivers	4
Number of Receivers	5
Operating Temperature (Max)	85 °C
Operating Temperature (Min)	-40 °C
Package Length	0.295 in
Package Name	28-SOIC
Package Width	7.5 mm
Protocol	RS232
Receiver Hysteresis	500 mV
Type	Transceiver
Voltage - Supply (Maximum)	5.5 V
Voltage - Supply (Minimum)	4.5 V

MAX211 Series

Part	Receiver Hysteresis	Protocol	Number of Receivers	Number of Drivers	Voltage - Supply (Maximum)	Voltage - Supply (Minimum)	Mounting Type	Duplex	Data Rate	Operating Temperature (Max)	Operating Temperature (Min)	Package Width	Package Name	Package Length	Type
Texas Instruments MAX211CDBR	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	70 °C	0 °C	5.3 mm	28-SSOP	0.209 in	Transceiver
Texas Instruments MAX211IDBRG4	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	85 °C	-40 °C	5.3 mm	28-SSOP	0.209 in	Transceiver
Texas Instruments MAX211CDWR	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	70 °C	0 °C	7.5 mm	28-SOIC	0.295 in	Transceiver
Texas Instruments MAX211IDBRE4	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	85 °C	-40 °C	5.3 mm	28-SSOP	0.209 in	Transceiver
Texas Instruments MAX211IDWR	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	85 °C	-40 °C	7.5 mm	28-SOIC	0.295 in	Transceiver
Texas Instruments MAX211CDW	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	70 °C	0 °C	7.5 mm	28-SOIC	0.295 in	Transceiver
Texas Instruments MAX211IDBR	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	85 °C	-40 °C	5.3 mm	28-SSOP	0.209 in	Transceiver
Texas Instruments MAX211IDW	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	85 °C	-40 °C	7.5 mm	28-SOIC	0.295 in	Transceiver
Texas Instruments MAX211CDWG4	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	70 °C	0 °C	7.5 mm	28-SOIC	0.295 in	Transceiver
Texas Instruments MAX211IDB	500 mV	RS232	5	4	5.5 V	4.5 V	Surface Mount	Full	120 Kbps	85 °C	-40 °C	5.3 mm	28-SSOP	0.209 in	Transceiver

Pricing

Prices provided here are for design reference only. For realtime values and availability, please visit the distributors directly

Distributor	Package	Quantity	$	Updated

Digikey	Bulk	115	$ 2.60	1w
Texas Instruments	TUBE	1	$ 3.08	30d+
		100	$ 2.54
		250	$ 1.83
		1000	$ 1.37

CAD

3D models and CAD resources for this part

Description

General part information

MAX211 Series

The MAX211 device consists of four line drivers, five line receivers, and a dual charge-pump circuit with ±15kV ESD protection pin to pin (serial-port connection pins, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 5V supply. The devices operate at data signaling rates up to 120kbit/s and a maximum of 30V/µs driver output slew rate.

The MAX211 has both shutdown (SHDN) and enable control (EN). In shutdown mode, the charge pumps are turned off, V+ is pulled down to VCC, V− is pulled to GND, and the transmitter outputs are disabled. This reduces supply current typically to 1µA. EN is used to put the receiver outputs into the high-impedance state to allow wired-OR connection of two RS-232 ports. It has no effect on the RS-232 drivers or the charge pumps.

Documents

Technical documentation and resources

MAX211 5V Multichannel RS-232 Line Driver and Receiver with ±15kV ESD Protection datasheet (Rev. F)