74CB3Q6800 Series

3.3-V, 1:1 (SPST), 10-channel general-purpose FET bus switch with precharged outputs

Catalog(1 parts)

Part	Voltage Supply Source	Package / Case▲▼	Package / Case▲▼	Package / Case	Mounting Type	Independent Circuits▲▼	Type	Operating Temperature▲▼	Operating Temperature▲▼	Circuit	Circuit▲▼	Voltage - Supply▲▼	Voltage - Supply▲▼	Supplier Device Package
Texas Instruments SN74CB3Q6800PW Bus Switch 10 x 1:1 24-TSSOP	Single Supply	0.004399999976158142 m	0.004394200164824724 m	24-TSSOP	Surface Mount	1 ul	Bus Switch	-40 °C	85 °C	1:1	10 ul	3.5999999046325684 V	2.299999952316284 V	24-TSSOP

Key Features

• High-Bandwidth Data Path (Up To 500 MHz)5-V Tolerant I/Os with Device Powered-Up or Powered-DownLow and Flat ON-State Resistance (ron) Characteristics Over Operating Range (ron= 4.5Typical)Rail-to-Rail Switching on Data I/O Ports0- to 5-V Switching With 3.3-V VCC0- to 3.3-V Switching With 2.5-V VCCB-Port Outputs Are Precharged by Bias Voltage (BIASV) to Minimize Signal Distortion During Live Insertion and Hot-PluggingSupports PCI Hot PlugBidirectional Data Flow, With Near-Zero Propagation DelayLow Input/Output Capacitance Minimizes Loading and Signal Distortion (Cio(OFF)= 3.5 pF Typical)Fast Switching Frequency (fON\= 20 MHz Max)Data and Control Inputs Provide Undershoot Clamp DiodesLow Power Consumption (ICC= 0.75 mA Typical)VCCOperating Range From 2.3 V to 3.6 VData I/Os Support 0 to 5-V Signaling Levels (0.8-V, 1.2-V, 1.5-V, 1.8-V, 2.5-V, 3.3-V, 5-V)Control Inputs Can be Driven by TTL or 5-V/3.3-V CMOS OutputsIoffSupports Partial-Power-Down Mode OperationLatch-Up Performance Exceeds 100 mA Per JESD 78, Class IIESD Performance Tested Per JESD 222000-V Human-Body Model (A114-B, Class II)1000-V Charged-Device Model (C101)Supports Both Digital and Analog Applications: PCI Interface, Differential Signal Interface, Memory Interleaving, Bus Isolation, Low-Distortion Signal GatingFor additional information regarding the performance characteristics of the CB3Q family, refer to the TI application report,CBT-C, CB3T, and CB3Q Signal-Switch Families, literature number SCDA008.High-Bandwidth Data Path (Up To 500 MHz)5-V Tolerant I/Os with Device Powered-Up or Powered-DownLow and Flat ON-State Resistance (ron) Characteristics Over Operating Range (ron= 4.5Typical)Rail-to-Rail Switching on Data I/O Ports0- to 5-V Switching With 3.3-V VCC0- to 3.3-V Switching With 2.5-V VCCB-Port Outputs Are Precharged by Bias Voltage (BIASV) to Minimize Signal Distortion During Live Insertion and Hot-PluggingSupports PCI Hot PlugBidirectional Data Flow, With Near-Zero Propagation DelayLow Input/Output Capacitance Minimizes Loading and Signal Distortion (Cio(OFF)= 3.5 pF Typical)Fast Switching Frequency (fON\= 20 MHz Max)Data and Control Inputs Provide Undershoot Clamp DiodesLow Power Consumption (ICC= 0.75 mA Typical)VCCOperating Range From 2.3 V to 3.6 VData I/Os Support 0 to 5-V Signaling Levels (0.8-V, 1.2-V, 1.5-V, 1.8-V, 2.5-V, 3.3-V, 5-V)Control Inputs Can be Driven by TTL or 5-V/3.3-V CMOS OutputsIoffSupports Partial-Power-Down Mode OperationLatch-Up Performance Exceeds 100 mA Per JESD 78, Class IIESD Performance Tested Per JESD 222000-V Human-Body Model (A114-B, Class II)1000-V Charged-Device Model (C101)Supports Both Digital and Analog Applications: PCI Interface, Differential Signal Interface, Memory Interleaving, Bus Isolation, Low-Distortion Signal GatingFor additional information regarding the performance characteristics of the CB3Q family, refer to the TI application report,CBT-C, CB3T, and CB3Q Signal-Switch Families, literature number SCDA008.

Description

The SN74CB3Q6800 is a high-bandwidth FET bus switch utilizing a charge pump to elevate the gate voltage of the pass transistor, providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance allows for minimal propagation delay and supports rail-to-rail switching on the data input/output (I/O) ports. The device also features low data I/O capacitance to minimize capacitive loading and signal distortion on the data bus. Specifically designed to support high-bandwidth applications, the SN74CB3Q6800 provides an optimized interface solution ideally suited for broadband communications, networking, and data-intensive computing systems. The SN74CB3Q6800 is a 10-bit bus switch with a single output-enable (ON\) input. When ON\ is low, the 10-bit bus switch is ON and the A port is connected to the B port, allowing bidirectional data flow between ports. When ON\ is high, the 10-bit bus switch is OFF and a high-impedance state exists between the A and B ports. The B port is precharged to bias voltage (BIASV) through the equivalent of a 10-kresistor when ON\ is high, or if the device is powered down (VCC= 0 V). During insertion (or removal) of a card into (or from) an active bus, the card’s output voltage may be close to GND. When the connector pins make contact, the card’s parasitic capacitance tries to force the bus signal to GND, creating a possible glitch on the active bus. This glitching effect can be reduced by using a bus switch with precharged bias voltage (BIASV) of the bus switch equal to the input threshold voltage level of the receivers on the active bus. This method will ensure that any glitch produced by insertion (or removal) of the card will not cross the input threshold region of the receivers on the active bus, minimizing the effects of live-insertion noise. This device is fully specified for partial-power-down applications using Ioff. The Ioffcircuitry prevents damaging current backflow through the device when it is powered down. The device has isolation during power off. To ensure the high-impedance state during power up or power down, ON\ should be tied to VCCthrough a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. The SN74CB3Q6800 is a high-bandwidth FET bus switch utilizing a charge pump to elevate the gate voltage of the pass transistor, providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance allows for minimal propagation delay and supports rail-to-rail switching on the data input/output (I/O) ports. The device also features low data I/O capacitance to minimize capacitive loading and signal distortion on the data bus. Specifically designed to support high-bandwidth applications, the SN74CB3Q6800 provides an optimized interface solution ideally suited for broadband communications, networking, and data-intensive computing systems. The SN74CB3Q6800 is a 10-bit bus switch with a single output-enable (ON\) input. When ON\ is low, the 10-bit bus switch is ON and the A port is connected to the B port, allowing bidirectional data flow between ports. When ON\ is high, the 10-bit bus switch is OFF and a high-impedance state exists between the A and B ports. The B port is precharged to bias voltage (BIASV) through the equivalent of a 10-kresistor when ON\ is high, or if the device is powered down (VCC= 0 V). During insertion (or removal) of a card into (or from) an active bus, the card’s output voltage may be close to GND. When the connector pins make contact, the card’s parasitic capacitance tries to force the bus signal to GND, creating a possible glitch on the active bus. This glitching effect can be reduced by using a bus switch with precharged bias voltage (BIASV) of the bus switch equal to the input threshold voltage level of the receivers on the active bus. This method will ensure that any glitch produced by insertion (or removal) of the card will not cross the input threshold region of the receivers on the active bus, minimizing the effects of live-insertion noise. This device is fully specified for partial-power-down applications using Ioff. The Ioffcircuitry prevents damaging current backflow through the device when it is powered down. The device has isolation during power off. To ensure the high-impedance state during power up or power down, ON\ should be tied to VCCthrough a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.