Zenode.ai Logo

UCC38083 Series

Current mode push-pull PWM with prog. slope comp, 3.5ms soft start, 12.5/8.3 UVLO, 0°C to 70°C

Manufacturer: Texas Instruments

Catalog(4 parts)

PartDuty CycleFrequency - SwitchingFrequency - SwitchingFault ProtectionInternal Switch(s)Operating TemperatureOperating TemperatureVoltage - Start UpControl FeaturesPackage / CaseSupplier Device PackageVoltage - Supply (Vcc/Vdd)Voltage - Supply (Vcc/Vdd)TopologyMounting TypeOutput IsolationPackage / CasePackage / Case
Texas Instruments
UCC38083PW
Converter Offline Push-Pull Topology 50kHz ~ 1MHz 8-TSSOP
0.4900000095367432 ul
50000 Hz
1000000 Hz
Current Limiting
70 °C
0 °C
12.5 V
Frequency Control
8-TSSOP (0.173", 4.40mm Width)
8-TSSOP
15 V
8.300000190734863 V
Push-Pull
Surface Mount
Isolated
Texas Instruments
UCC38083D
Converter Offline Push-Pull Topology 50kHz ~ 1MHz 8-SOIC
0.4900000095367432 ul
50000 Hz
1000000 Hz
Current Limiting
70 °C
0 °C
12.5 V
Frequency Control
8-SOIC
8-SOIC
15 V
8.300000190734863 V
Push-Pull
Surface Mount
Isolated
0.003899999894201755 m
Texas Instruments
UCC38083P
Converter Offline Push-Pull Topology 50kHz ~ 1MHz 8-PDIP
0.4900000095367432 ul
50000 Hz
1000000 Hz
Current Limiting
70 °C
0 °C
12.5 V
Frequency Control
8-DIP
8-PDIP
15 V
8.300000190734863 V
Push-Pull
Through Hole
Isolated
0.007619999814778566 m
0.007619999814778566 m
Texas Instruments
UCC38083PWRG4
Converter Offline Push-Pull Topology 50kHz ~ 1MHz 8-TSSOP
0.4900000095367432 ul
50000 Hz
1000000 Hz
Current Limiting
70 °C
0 °C
12.5 V
Frequency Control
8-TSSOP (0.173", 4.40mm Width)
8-TSSOP
15 V
8.300000190734863 V
Push-Pull
Surface Mount
Isolated

Key Features

Programmable Slope CompensationInternal Soft-Start on the UCC38083/4Cycle-by-Cycle Current LimitingLow Start-Up Current of 120 µA and 1.5 mA Typical Run CurrentSingle External Component Oscillator Programmable from 50 kHz to 1 MHzHigh-Current Totem-Pole Dual Output Stage Drives Push-Pull Configuration with 1-A Sink and 0.5-A Source CapabilityCurrent Sense Discharge Transistor to Improve Dynamic ResponseInternally Trimmed Bandgap ReferenceUndervoltage Lockout with HysteresisAPPLICATIONSHigh-Efficiency Switch-Mode Power SuppliesTelecom dc-to-dc ConvertersPoint-of-Load or Point-of-Use Power ModulesLow-Cost Push-Pull and Half-Bridge ApplicationsProgrammable Slope CompensationInternal Soft-Start on the UCC38083/4Cycle-by-Cycle Current LimitingLow Start-Up Current of 120 µA and 1.5 mA Typical Run CurrentSingle External Component Oscillator Programmable from 50 kHz to 1 MHzHigh-Current Totem-Pole Dual Output Stage Drives Push-Pull Configuration with 1-A Sink and 0.5-A Source CapabilityCurrent Sense Discharge Transistor to Improve Dynamic ResponseInternally Trimmed Bandgap ReferenceUndervoltage Lockout with HysteresisAPPLICATIONSHigh-Efficiency Switch-Mode Power SuppliesTelecom dc-to-dc ConvertersPoint-of-Load or Point-of-Use Power ModulesLow-Cost Push-Pull and Half-Bridge Applications

Description

AI
The UCC38083/4/5/6 is a family of BiCMOS pulse width modulation (PWM) controllers for dc-to-dc or off-line fixed-frequency current-mode switching power supplies. The dual output stages are configured for the push-pull topology. Both outputs switch at half the oscillator frequency using a toggle flip-flop. The dead time between the two outputs is typically 110 ns, limiting each output’s duty cycle to less than 50%. The new UCC3808x family is based on the UCC3808A architecture. The major differences include the addition of a programmable slope compensation ramp to the CS signal and the removal of the error amplifier. The current flowing out of the ISET pin through an external resistor is monitored internally to set the magnitude of the slope compensation function. This device also includes an internal discharge transistor from the CS pin to ground, which is activated at each clock cycle after the pulse is terminated. This discharges any filter capacitance on the CS pin during each cycle and helps minimize filter capacitor values and current sense delay. The UCC38083 and the UCC38084 devices have a typical soft-start interval time of 3.5 ms while the UCC38085 and the UCC38086 has less than 100 µs for applications where internal soft-start is not desired. The UCC38083 and the UCC38085 devices have the turn on/off thresholds of the 12.5 V / 8.3 V, while the UCC38084 and the UCC38086 has the turn on/off thresholds of 4.3 V / 4.1 V. Each device is offered in 8-pin TSSOP (PW), 8-pin SOIC (D) and 8-pin PDIP (P) packages. The UCC38083/4/5/6 is a family of BiCMOS pulse width modulation (PWM) controllers for dc-to-dc or off-line fixed-frequency current-mode switching power supplies. The dual output stages are configured for the push-pull topology. Both outputs switch at half the oscillator frequency using a toggle flip-flop. The dead time between the two outputs is typically 110 ns, limiting each output’s duty cycle to less than 50%. The new UCC3808x family is based on the UCC3808A architecture. The major differences include the addition of a programmable slope compensation ramp to the CS signal and the removal of the error amplifier. The current flowing out of the ISET pin through an external resistor is monitored internally to set the magnitude of the slope compensation function. This device also includes an internal discharge transistor from the CS pin to ground, which is activated at each clock cycle after the pulse is terminated. This discharges any filter capacitance on the CS pin during each cycle and helps minimize filter capacitor values and current sense delay. The UCC38083 and the UCC38084 devices have a typical soft-start interval time of 3.5 ms while the UCC38085 and the UCC38086 has less than 100 µs for applications where internal soft-start is not desired. The UCC38083 and the UCC38085 devices have the turn on/off thresholds of the 12.5 V / 8.3 V, while the UCC38084 and the UCC38086 has the turn on/off thresholds of 4.3 V / 4.1 V. Each device is offered in 8-pin TSSOP (PW), 8-pin SOIC (D) and 8-pin PDIP (P) packages.