5962-8951106 Series
Space-grade QMLV, 35-V, dual 0.4-A 400-kHz PWM controller
Manufacturer: Texas Instruments
Catalog(1 parts)
| Part | Package / Case | Control Features | Mounting Type | Duty Cycle (Max)▲▼ | Output Configuration | Frequency - Switching▲▼ | Frequency - Switching▲▼ | Supplier Device Package▲▼ | Supplier Device Package | Supplier Device Package▲▼ | Number of Outputs▲▼ | Clock Sync▲▼ | Voltage - Supply (Vcc/Vdd)▲▼ | Voltage - Supply (Vcc/Vdd)▲▼ | Synchronous Rectifier▲▼ | Output Phases▲▼ | Topology | Operating Temperature▲▼ | Operating Temperature▲▼ | Function | Output Type |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Texas Instruments 5962-8951106V2AFull-Bridge, Half-Bridge, Push-Pull Regulator Positive Output Step-Up, Step-Up/Step-Down DC-DC Controller IC 20-LCCC (8.89x8.89) | 20-CLCC | Dead Time Control, Enable, Frequency Control, Soft Start | Surface Mount | 0.4900000095367432 ul | Positive | 100000 Hz | 400000 Hz | 8.890000343322754 ul | 20-LCCC | 8.890000343322754 ul | 2 ul | 35 V | 8 V | 1 ul | Full-Bridge, Half-Bridge, Push-Pull | -55 °C | 125 °C | Step-Up, Step-Up/Step-Down | Transistor Driver |
Key Features
• QML-V Qualified, SMD 5962-89511Rad-Tolerant: 30 kRad (Si) TID(1)8-V to 35-V Operation5.1-V Buried Zener Reference Trimmed to ±0.75%100-Hz to 400-kHz Oscillator RangeSeparate Oscillator Sync TerminalAdjustable Deadtime ControlInternal Soft StartPulse-by-Pulse ShutdownInput Undervoltage Lockout With HysteresisLatching PWM to Prevent Multiple PulsesDual Source/Sink Output DriversLow Cross Conduction Output StageTighter Reference Specifications(1)Radiation tolerance is a typical value based upon initial device qualification with dose rate = 10 mrad/sec. Radiation Lot Acceptance Testing is available - contact factory for details.QML-V Qualified, SMD 5962-89511Rad-Tolerant: 30 kRad (Si) TID(1)8-V to 35-V Operation5.1-V Buried Zener Reference Trimmed to ±0.75%100-Hz to 400-kHz Oscillator RangeSeparate Oscillator Sync TerminalAdjustable Deadtime ControlInternal Soft StartPulse-by-Pulse ShutdownInput Undervoltage Lockout With HysteresisLatching PWM to Prevent Multiple PulsesDual Source/Sink Output DriversLow Cross Conduction Output StageTighter Reference Specifications(1)Radiation tolerance is a typical value based upon initial device qualification with dose rate = 10 mrad/sec. Radiation Lot Acceptance Testing is available - contact factory for details.
Description
AI
The UC1525B pulse width modulator integrated circuit is designed to offer improved performance and lowered external parts count when used in designing all types of switching power supplies. The on-chip 5.1-V buried zener reference is trimmed to ±0.75%, and the input common-mode range of the error amplifier includes the reference voltage, eliminating external resistors. A sync input to the oscillator allows multiple units to be slaved or a single unit to be synchronized to an external system clock. A single resistor between the CT and the discharge terminals provide a wide range of dead-time adjustment. These devices also feature built-in soft-start circuitry with only an external timing capacitor required. A shutdown terminal controls both the soft-start circuitry and the output stages, providing instantaneous turn off through the PWM latch with pulsed shutdown, as well as soft-start recycle with longer shutdown commands. These functions are also controlled by an undervoltage lockout which keeps the outputs off and the soft-start capacitor discharged for sub-normal input voltages. This lockout circuitry includes approximately 500 mV of hysteresis for jitter-free operation. Another feature of these PWM circuits is a latch following the comparator. Once a PWM pulse has been terminated for any reason, the outputs remain off for the duration of the period. The latch is reset with each clock pulse. The output stages are totem-pole designs capable of sourcing or sinking in excess of 200 mA. The UC1525B output stage features NOR logic, giving a LOW output for an OFF state.
The UC1525B pulse width modulator integrated circuit is designed to offer improved performance and lowered external parts count when used in designing all types of switching power supplies. The on-chip 5.1-V buried zener reference is trimmed to ±0.75%, and the input common-mode range of the error amplifier includes the reference voltage, eliminating external resistors. A sync input to the oscillator allows multiple units to be slaved or a single unit to be synchronized to an external system clock. A single resistor between the CT and the discharge terminals provide a wide range of dead-time adjustment. These devices also feature built-in soft-start circuitry with only an external timing capacitor required. A shutdown terminal controls both the soft-start circuitry and the output stages, providing instantaneous turn off through the PWM latch with pulsed shutdown, as well as soft-start recycle with longer shutdown commands. These functions are also controlled by an undervoltage lockout which keeps the outputs off and the soft-start capacitor discharged for sub-normal input voltages. This lockout circuitry includes approximately 500 mV of hysteresis for jitter-free operation. Another feature of these PWM circuits is a latch following the comparator. Once a PWM pulse has been terminated for any reason, the outputs remain off for the duration of the period. The latch is reset with each clock pulse. The output stages are totem-pole designs capable of sourcing or sinking in excess of 200 mA. The UC1525B output stage features NOR logic, giving a LOW output for an OFF state.