The Microchip USB7052N [SmartHub](https://www.microchip.com/en-us/products/interface-and-connectivity/usb/usb-hubs/smarthub-ics)™ IC is a low-power, OEM configurable, USB3.2 Gen 1 hub controller with 4 downstream ports and advanced features for embedded USB applications. The USB7052N is fully compliant with the Universal Serial Bus Revision 3.2 Specification and USB2.0 Link Power Management Addendum. The USB7052N supports 5 Gbps Super-Speed (SS), 480 Mbps Hi-Speed (HS), 12 Mbps Full-Speed (FS), and 1.5 Mbps Low-Speed (LS) USB downstream devices on all enabled downstream ports. A SmartHub IC is defined as a USB hub that integrates system levels functions typically associated with a separate MCU or processor. The USB7052N SmartHub IC enables communication to other peripherals in addition to USB. This I/O Bridging capability allows the host to seamlessly interface to peripherals via I²C, SPI or GPIOs over USB. The USB7052N also enable a downstream device to take control of the host system by swapping roles and becoming the host port. The USB7052N can also switch between two different hosts if required. This role changing technology is called FlexConnect and can be initiated through hardware or software commands. The USB7052N supports native Type-C connectivity on two of the downstream ports. The hub includes internal Type-C CC pin logic and an internal USB 3.2 Gen 1 multiplexer to support both Type-C insertion orientations. The USB7052N supports an additional 2 x Type A ports downstream - 1 x USB3.2 Gen1 and 1 x USB2.0. The hub also supports legacy USB speeds (HS/FS/LS) through a dedicated USB2.0 hub controller that is the culmination of six generations of Microchip hub feature controller design and experience with proven reliability, interoperability, and device compatibility. The SuperSpeed hub controller operates in parallel with the USB2.0 controller, decoupling the 5 Gbps SS data transfers from bottlenecks due to the slower USB 2.0 traffic. The USB7052N supports downstream battery charging and integrated battery charger detection circuitry supporting the USB-IF Battery Charging (BC1.2) detection method and most Apple® devices. The USB7052N provides the battery charging handshake and supports the following USB-IF BC1.2 charging profiles: **•** DCP: Dedicated Charging Port (Power brick with no data) **•** CDP: Charging Downstream Port (1.5A with data) **•** SDP: Standard Downstream Port (0.5A with data) **•** Custom profiles loaded via SPI EEPROM or OTP MPLAB® Connect Configurator, Microchip’s proprietary software utility, can be used to program On-chip One Time Programmable (OTP) ROM for the USB7052N which stores required register settings to ensure the desired start up configuration at power on. All LED, GPIOs and port control signal pins are under firmware control, allowing for maximum operational flexibility. However, for even more simplicity, the USB7052N can be configured through a series of external low-cost resistor bootstraps. A handful of bootstrap pins are available on the USB7052N to enable standard configurations for GPIOs and downstream ports. No OTP programming required. **Unlike the USB7050/51/52/56, USB7052N applications DO NOT require application-specific firmware developed by Microchip support engineers. There is no native PD firmware included within the USB7052N.** Microchip's complimentary and confidential [MicroCHECK](https://www.microchip.com/en-us/support/design-help/design-check-services) design review service, which offers insight from the initial concept to the final PCB layout, is available to customers who are using our products in their projects. You can confidently submit your design materials in a secure and private setting, and our expert engineers will provide individualized feedback to enhance your design. MicroCHECK design review service is subject to Microchip's [Program Terms and Conditions](https://www.microchip.com/en-us/support/design-help/design-check-services/design-check-services-program-terms-and-conditions) and requires a myMicrochip account.