dsPIC33AK32MC106 Series

200 MHz 32-bit Single-Core Digital Signal Controller (DSC)

Catalog

200 MHz 32-bit Single-Core Digital Signal Controller (DSC)

Part
Microchip Technology DSPIC33AK32MC106T-E/M7

Catalog

200 MHz 32-bit Single-Core Digital Signal Controller (DSC)

Key Features

• Operating Conditions* 3.0V to 3.6V: -40°C to +85°C, DC to 200 MHz

• * 3.0V to 3.6V: -40°C to +150°C, DC to 200 MHz

• * 3.0V to 3.6V: -40°C to +125°C, DC to 200 MHz

•

• High-Performance dsPIC33A Digital Signal Controller (DSC)* 32-bit Rich Instruction Set for Optimized Speed and Program Code Size:

• * Non-paged linear Data/Flash 24-bit addressing space

• * 16-bit/32-bit instructions for optimized code size and performance

• * 32-bit Wide Data Paths

• * Single and Double Precision Floating-Point Unit (FPU) Coprocessor

• * Edge or Level Change Notification Interrupt on I/O pins

• * Peripheral Pin Select (PPS) Remappable Pins to Reduce Board Layout Complexity

• * Multiple Interrupt Vectors with Individual Programmable Priority

• * Five External Interrupt Pins

• * Selectable Oscillator Options Including:

• * 8 MHz, 1% at 0ºC-85ºC Internal Fast RC (FRC) oscillator

• * 8 MHz, 2% Internal Backup Fast RC (BFRC) oscillator with 32 kHz divided output

• * 2 Kbyte Instruction Cache

• * Sixteen 32-bit Working Registers

• * Dual 72-bit Accumulators Supporting 32-bit and 16-bit Fixed-Point DSP Operations

• * Eight Level Deep Working Register Sets

• * Eight Level Deep Accumulator Register Sets

• * Eight Level Deep Floating Point Register Sets

•

• Memory Features* Up to 128 Kbytes of Program Flash Memory:

• * 10,000 erase/write cycle endurance

• * 20 years minimum data retention

• * Self-programmable under software control

• * Programmable code protection

• * Flash Error Correcting Code (ECC)

• * Programmable OTP regions

• * Entire Flash OTP by ICSP™ write inhibit

• * 64 x128-bit OTP area

• * High-speed crystal resonator oscillator or external clock

• * Up to 16 Kbytes of RAM Memory:

• * 6-channel hardware Direct Memory Access (DMA) module

• * RAM Error Correcting Code (ECC)

• * RAM Memory Built-In Self-Test (MBIST)

•

• Controller Features* High-Current Sink/Source Capable I/Os

• * Programmable Weak Pull-Up and Pull-Down Resistors

• * Programmable Open-Drain Outputs

• * Two 1.6 GHz PLLs for Peripheral which can be clocked from the FRC or a Crystal Oscillator

• * Reference Clock Output (REFO)

• * Low-Power Management Modes (Sleep and Idle)

• * Power-On Reset and Brown-Out Reset

•

• High-Speed PWM* Four PWM Generators (Four Pairs, Eight Outputs)

• * Up to 2.5 ns PWM Resolution

• * Dead Time for Rising and Falling Edges

• * Dead-Time Compensation Supports Lower Speed Operation

• * PWM Support for:

• * BLDC, PMSM, ACIM, SRM and stepper motors

• * Fault and Current Limit Inputs

• * Flexible Trigger Configuration for ADC Triggering

•

• Two High-Speed Analog-to-Digital Converters* 12-bit Resolution

• * Up to 40 MSPS Conversion Rate

• * Up to 22 Analog Input Pins

• * 20 Settings Channels. Each Channel:

• * Can be assigned to any analog input (I/O pin or internal signal)

• * Can be set to a different sampling time

• * Can be configured as single-ended or differential

• * Conversion result can be formatted as unsigned or signed

• * Conversion result can be left-aligned (fraction format)

• * Has a separate 32-bit conversion result register

• * Supports Four Sampling modes:

• * Oversampling of multiple samples

• * Integration of multiple samples

• * Window (multiple samples accumulated when the gate signal is active)

• * Single Conversion

• * All channels have a digital comparator to detect when the conversion result is less than, greater than, in bounds or out of bounds for the configurable thresholds

• * Last three settings channels have the second result accumulator to implement second order filters

• * Band Gap Reference and Temperature Sensor Diode Inputs

•

• Other Analog Features* Three 5 nS Analog Comparators with 12-bit PDM DACs:

• * Input multiplexing

• * Slope compensation

• * One DAC output buffer

• * Eight Constant-Current Sources

•

• Up to 3 Rail-to-Rail 100 MHz Operational Amplifiers with* 100 V/μS slew rate

• * 1 mV offset (typical)

• * User calibration of input offset voltage

•

• Peripheral Features* Three 4-Wire SPI Modules:

• * 32-byte FIFO

• * Variable data width

• * I2S mode

• * Two I2C Modules w/Address Masking and IPMI Support

• * Three Protocol UARTs with 8-bit RX/TX FIFOs and Automated Handling Support for:

• * LIN 2.2

• * DMX

• * Smart card (ISO 7816)

• * IrDA®

• * Two SENT Modules

• * One Dedicated 32-bit Timer/Counter

• * Four Single Output Capture/Compare/PWM/Timer (SCCP) Modules:

• * Flexible configuration as PWM, input capture, output compare or timers

• * Two 16-bit timers or one 32-bit timer in each module

• * Single PWM output pin

• * One Quadrature Encoder Interface (QEI):

• * Four inputs: Phase A, Phase B, Home, Index

• * Four Configurable Logic Cells (CLC) with Internal Connections to Select Peripherals and PPS

• * Serial Encoder Interface BiSS with up to Four Client Encoders Support

• * Peripheral Trigger Generator (PTG):

• * 10 input trigger sources from other peripheral modules

• * 5 output triggers to other peripheral modules

• * 4 individual interrupt request signals

• * CPU independent state machine-based instruction sequencer

•

• Security Module* Immutable Root of Trust (IRT)

• * Configurable Flash protection regions

• * Flash access control

• * Secure Boot

• * Secure Debug

• * Device locking

•

• Safety Features* Windowed Watchdog Timer (WDT)

• * Deadman Timer (DMT)

• * Four I/O Integrity Monitors (IOIM)

• * Fail-Safe Clock Monitor (FSCM) with Automatic Switchover to Backup Clock Source with:

• * Programmable over-frequency/under-frequency thresholds

• * Flash Error Correcting Code (ECC)

• * RAM Error Correcting Code (ECC)

• * RAM Memory Built-In Self-Test (MBIST)

• * 32-bit Cyclic Redundancy Check (CRC) Module

• * Entire Flash OTP by ICSP™ Write Inhibit

• * Capless Internal Voltage Regulator

• * Virtual PPS Pins for Redundancy and Monitoring

• * Temperature Sensor Diode

•

• Functional Safety* Functional Safety Readiness – ISO 26262/IEC 61508/IEC 60730.

•

• Qualification* AEC-Q100 REV H:

• * Grade 1: -40°C to +125°C

• * Grade 0: -40°C to +150°C Planned

•

• Programming and Debug Interfaces* Three Programming and Debugging Interfaces:

• * Two-wire ICSP™ interface with non-intrusive access and real-time data exchange with application

• * Five Program Addresses and Five Full-Featured Breakpoints

• * IEEE Standard 1149.2 Compatible (JTAG) Boundary Scan

Description

200MHz, 32-bit dsPIC33A Digital Signal Controller (DSC) with 32/64bit Floating-Point Unit (FPU) and up to 128KB Flash Program Memory and 16KB SRAM Data Memory. High-speed 40MSPS 12-bit ADCs, high-bandwidth 100MHz op amps with low input voltage offset, fast 5nS comparators and high-speed PWM outputs designed to optimize real-time control applications. [Functional Safety Ready](https://www.microchip.com/en-us/products/microcontrollers-and-microprocessors/dspic-dscs/functional-safety) with AEC-Q100 qualification support for automotive applications.