SST49LF080 Series

3.0V to 3.6V 8Mbit Firmware Flash

Catalog

3.0V to 3.6V 8Mbit Firmware Flash

Part	Memory Size	Memory Type	Memory Format	Mounting Type	Access Time	Supplier Device Package	Supplier Device Package [x]	Supplier Device Package [y]	Voltage - Supply [Max]	Voltage - Supply [Min]	Clock Frequency	Operating Temperature [Min]	Operating Temperature [Max]	Technology	Memory Organization [custom]	Memory Organization [custom]	Write Cycle Time - Word, Page [custom]	Write Cycle Time - Word, Page [custom]	Memory Interface	Package / Case	Package / Case [y]	Package / Case [y]
Microchip Technology SST49LF080A-33-4C-NHE-T	1024 KB	Non-Volatile	FLASH	Surface Mount	120 ns	32-PLCC	11.43	13.97	3.6 V	3 V	33 MHz	0 °C	85 C	FLASH	1 M	8 bits	20 µs	20 µs	Parallel	32-LCC (J-Lead)
Microchip Technology SST49LF080A-33-4C-WHE-T	1024 KB	Non-Volatile	FLASH	Surface Mount	120 ns	32-TSOP			3.6 V	3 V	33 MHz	0 °C	85 C	FLASH	1 M	8 bits	20 µs	20 µs	Parallel	32-TFSOP	0.488 in	12.4 mm

Catalog

3.0V to 3.6V 8Mbit Firmware Flash

Key Features

- LPC Interface Flash

• – SST49LF080A: 1024K x8 (8 Mbit)

- Conforms to Intel LPC Interface Specification 1.0

- Flexible Erase Capability

• – Uniform 4 KByte Sectors

• – Uniform 64 KByte overlay blocks

• – 64 KByte Top Boot Block protection

• – Chip-Erase for PP Mode Only

- Single 3.0-3.6V Read and Write Operations

- Superior Reliability

• – Endurance: 100,000 Cycles (typical)

• – Greater than 100 years Data Retention

- Low Power Consumption

• – Active Read Current: 6 mA (typical)

• – Standby Current: 10 µA (typical)

- Fast Sector-Erase/Byte-Program Operation

• – Sector-Erase Time: 18 ms (typical)

• – Block-Erase Time: 18 ms (typical)

• – Chip-Erase Time: 70 ms (typical)

• – Byte-Program Time: 14 µs (typical)

• – Chip Rewrite Time: 16 seconds (typical)

• – Single-pulse Program or Erase

• – Internal timing generation

- Two Operational Modes

• – Low Pin Count (LPC) Interface mode for

• in-system operation

• – Parallel Programming (PP) Mode for fast production

• programming

- LPC Interface Mode

• – 5-signal communication interface supporting

• byte Read and Write

• – 33 MHz clock frequency operation

• – WP# and TBL# pins provide hardware write protect

• for entire chip and/or top boot block

• – Standard SDP Command Set

• – Data# Polling and Toggle Bit for End-of-Write

• detection

• – 5 GPI pins for system design flexibility

• – 4 ID pins for multi-chip selection

- Parallel Programming (PP) Mode

• – 11-pin multiplexed address and 8-pin data

• I/O interface

• – Supports fast programming In-System on

• programmer equipment

- CMOS and PCI I/O Compatibility

- Packages Available– 32-lead PLCC

- All non-Pb (lead-free) devices are RoHS compliant

Description

The SST49LF080A flash memory device is designed to interface with the LPC bus for PC and Internet Appliance application in compliance with Intel Low Pin Count (LPC) Interface Specification 1.0. Two interface modes are supported: LPC mode for in-system operations and Parallel Programming (PP) mode to interface with programming equipment. The SST49LF080A flash memory device is manufactured with SST's proprietary, high-performance SuperFlash Technology. The split-gate cell design and thick-oxide tunneling injector attain better reliability and manufacturability compared with alternate approaches.